Analog and RF
Analog components, RF blocks, servo and bench instruments.
25 symbols. Generated from the symbol registry — see the note in the index.
Components
Capacitor
Key: analog.capacitor
Ports — p1 (analog), p2 (analog)
Ground
Key: analog.gnd
Ports — p1 (analog)
Inductor
Key: analog.inductor
Ports — p1 (analog), p2 (analog)
Op-amp
Key: analog.opamp
Ports — in1 (analog), in2 (analog), out (analog)
Resistor
Key: analog.resistor
Ports — p1 (analog), p2 (analog)
Voltage Source
Key: analog.vsource
Ports — p1 (analog), p2 (analog)
Instruments
AWG
Key: analog.awg
Ports — out (analog)
Its parameters change which ports it has; these are the defaults.
| Parameter | Default | Accepts |
|---|---|---|
outputs |
1 |
1, 2 |
Frequency Counter
Key: analog.freq_counter
Ports — in (analog)
Its parameters change which ports it has; these are the defaults.
| Parameter | Default | Accepts |
|---|---|---|
inputs |
1 |
1, 2 |
Function Generator
Key: analog.func_gen
Ports — out (analog)
Its parameters change which ports it has; these are the defaults.
| Parameter | Default | Accepts |
|---|---|---|
outputs |
1 |
1, 2 |
Phase Noise
Key: analog.phase_noise
Ports — in (analog)
Its parameters change which ports it has; these are the defaults.
| Parameter | Default | Accepts |
|---|---|---|
inputs |
1 |
1, 2 |
Scope
Key: analog.scope
Ports — in1 (analog), in2 (analog), in3 (analog), in4 (analog)
Spectrum Analyser
Key: analog.spec_an
Ports — in (analog)
Its parameters change which ports it has; these are the defaults.
| Parameter | Default | Accepts |
|---|---|---|
inputs |
1 |
1, 2 |
RF Blocks
Attenuator
Key: analog.attenuator
Ports — in (analog), n (analog), out (analog), s (analog)
| Parameter | Default | Accepts |
|---|---|---|
db |
3 |
0 to 60 dB, step 1 |
Bias Tee
Key: analog.bias_tee
Ports — dc (analog), out (analog), rf (analog), s (analog)
Directional Coupler
Key: analog.dir_coupler
Ports — cpl (analog), in (analog), n (analog), out (analog)
RF Filter
Key: analog.filter
Ports — in (analog), n (analog), out (analog), s (analog)
| Parameter | Default | Accepts |
|---|---|---|
response |
lp |
lp, hp, bp, notch |
RF Mixer
Key: analog.mixer
Ports — if (analog), lo (analog), n (analog), rf (analog)
Phase Detector
Key: analog.phase_det
Ports — in1 (analog), in2 (analog), n (analog), out (analog)
RF Amplifier
Key: analog.rf_amp
Ports — in (analog), out (analog)
RF Splitter
Key: analog.splitter
Ports — in (analog), n (analog), out1 (analog), out2 (analog), s (analog)
VCO
Key: analog.vco
Ports — n (analog), out (analog), s (analog), tune (analog)
Servo
Adder
Key: analog.adder
Ports — e (analog), in_n (analog), in_s (analog), in_w (analog), n (analog), out (analog), s (analog), w (analog)
| Parameter | Default | Accepts |
|---|---|---|
op |
add |
add, subtract |
PID Servo
Key: analog.pid
Ports — in (analog), mon (analog), n (analog), out (analog)
Piezo Driver
Key: analog.piezo_drv
Ports — in (analog), n (analog), out (analog), s (analog)
Temperature Controller
Key: analog.temp_ctrl
Ports — in (analog), n (analog), out (analog), s (analog)